| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: seeq: Fix use after free vulnerability in ether3 Driver Due to Race Condition
In the ether3_probe function, a timer is initialized with a callback
function ether3_ledoff, bound to &prev(dev)->timer. Once the timer is
started, there is a risk of a race condition if the module or device
is removed, triggering the ether3_remove function to perform cleanup.
The sequence of operations that may lead to a UAF bug is as follows:
CPU0 CPU1
| ether3_ledoff
ether3_remove |
free_netdev(dev); |
put_devic |
kfree(dev); |
| ether3_outw(priv(dev)->regs.config2 |= CFG2_CTRLO, REG_CONFIG2);
| // use dev
Fix it by ensuring that the timer is canceled before proceeding with
the cleanup in ether3_remove. |
| In the Linux kernel, the following vulnerability has been resolved:
jfs: fix out-of-bounds in dbNextAG() and diAlloc()
In dbNextAG() , there is no check for the case where bmp->db_numag is
greater or same than MAXAG due to a polluted image, which causes an
out-of-bounds. Therefore, a bounds check should be added in dbMount().
And in dbNextAG(), a check for the case where agpref is greater than
bmp->db_numag should be added, so an out-of-bounds exception should be
prevented.
Additionally, a check for the case where agno is greater or same than
MAXAG should be added in diAlloc() to prevent out-of-bounds. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw88: always wait for both firmware loading attempts
In 'rtw_wait_firmware_completion()', always wait for both (regular and
wowlan) firmware loading attempts. Otherwise if 'rtw_usb_intf_init()'
has failed in 'rtw_usb_probe()', 'rtw_usb_disconnect()' may issue
'ieee80211_free_hw()' when one of 'rtw_load_firmware_cb()' (usually
the wowlan one) is still in progress, causing UAF detected by KASAN. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: avoid OOB when system.data xattr changes underneath the filesystem
When looking up for an entry in an inlined directory, if e_value_offs is
changed underneath the filesystem by some change in the block device, it
will lead to an out-of-bounds access that KASAN detects as an UAF.
EXT4-fs (loop0): mounted filesystem 00000000-0000-0000-0000-000000000000 r/w without journal. Quota mode: none.
loop0: detected capacity change from 2048 to 2047
==================================================================
BUG: KASAN: use-after-free in ext4_search_dir+0xf2/0x1c0 fs/ext4/namei.c:1500
Read of size 1 at addr ffff88803e91130f by task syz-executor269/5103
CPU: 0 UID: 0 PID: 5103 Comm: syz-executor269 Not tainted 6.11.0-rc4-syzkaller #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:93 [inline]
dump_stack_lvl+0x241/0x360 lib/dump_stack.c:119
print_address_description mm/kasan/report.c:377 [inline]
print_report+0x169/0x550 mm/kasan/report.c:488
kasan_report+0x143/0x180 mm/kasan/report.c:601
ext4_search_dir+0xf2/0x1c0 fs/ext4/namei.c:1500
ext4_find_inline_entry+0x4be/0x5e0 fs/ext4/inline.c:1697
__ext4_find_entry+0x2b4/0x1b30 fs/ext4/namei.c:1573
ext4_lookup_entry fs/ext4/namei.c:1727 [inline]
ext4_lookup+0x15f/0x750 fs/ext4/namei.c:1795
lookup_one_qstr_excl+0x11f/0x260 fs/namei.c:1633
filename_create+0x297/0x540 fs/namei.c:3980
do_symlinkat+0xf9/0x3a0 fs/namei.c:4587
__do_sys_symlinkat fs/namei.c:4610 [inline]
__se_sys_symlinkat fs/namei.c:4607 [inline]
__x64_sys_symlinkat+0x95/0xb0 fs/namei.c:4607
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f3e73ced469
Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 21 18 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fff4d40c258 EFLAGS: 00000246 ORIG_RAX: 000000000000010a
RAX: ffffffffffffffda RBX: 0032656c69662f2e RCX: 00007f3e73ced469
RDX: 0000000020000200 RSI: 00000000ffffff9c RDI: 00000000200001c0
RBP: 0000000000000000 R08: 00007fff4d40c290 R09: 00007fff4d40c290
R10: 0023706f6f6c2f76 R11: 0000000000000246 R12: 00007fff4d40c27c
R13: 0000000000000003 R14: 431bde82d7b634db R15: 00007fff4d40c2b0
</TASK>
Calling ext4_xattr_ibody_find right after reading the inode with
ext4_get_inode_loc will lead to a check of the validity of the xattrs,
avoiding this problem. |
| In the Linux kernel, the following vulnerability has been resolved:
drivers: media: dvb-frontends/rtl2830: fix an out-of-bounds write error
Ensure index in rtl2830_pid_filter does not exceed 31 to prevent
out-of-bounds access.
dev->filters is a 32-bit value, so set_bit and clear_bit functions should
only operate on indices from 0 to 31. If index is 32, it will attempt to
access a non-existent 33rd bit, leading to out-of-bounds access.
Change the boundary check from index > 32 to index >= 32 to resolve this
issue. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/iwcm: Fix WARNING:at_kernel/workqueue.c:#check_flush_dependency
In the commit aee2424246f9 ("RDMA/iwcm: Fix a use-after-free related to
destroying CM IDs"), the function flush_workqueue is invoked to flush the
work queue iwcm_wq.
But at that time, the work queue iwcm_wq was created via the function
alloc_ordered_workqueue without the flag WQ_MEM_RECLAIM.
Because the current process is trying to flush the whole iwcm_wq, if
iwcm_wq doesn't have the flag WQ_MEM_RECLAIM, verify that the current
process is not reclaiming memory or running on a workqueue which doesn't
have the flag WQ_MEM_RECLAIM as that can break forward-progress guarantee
leading to a deadlock.
The call trace is as below:
[ 125.350876][ T1430] Call Trace:
[ 125.356281][ T1430] <TASK>
[ 125.361285][ T1430] ? __warn (kernel/panic.c:693)
[ 125.367640][ T1430] ? check_flush_dependency (kernel/workqueue.c:3706 (discriminator 9))
[ 125.375689][ T1430] ? report_bug (lib/bug.c:180 lib/bug.c:219)
[ 125.382505][ T1430] ? handle_bug (arch/x86/kernel/traps.c:239)
[ 125.388987][ T1430] ? exc_invalid_op (arch/x86/kernel/traps.c:260 (discriminator 1))
[ 125.395831][ T1430] ? asm_exc_invalid_op (arch/x86/include/asm/idtentry.h:621)
[ 125.403125][ T1430] ? check_flush_dependency (kernel/workqueue.c:3706 (discriminator 9))
[ 125.410984][ T1430] ? check_flush_dependency (kernel/workqueue.c:3706 (discriminator 9))
[ 125.418764][ T1430] __flush_workqueue (kernel/workqueue.c:3970)
[ 125.426021][ T1430] ? __pfx___might_resched (kernel/sched/core.c:10151)
[ 125.433431][ T1430] ? destroy_cm_id (drivers/infiniband/core/iwcm.c:375) iw_cm
[ 125.441209][ T1430] ? __pfx___flush_workqueue (kernel/workqueue.c:3910)
[ 125.473900][ T1430] ? _raw_spin_lock_irqsave (arch/x86/include/asm/atomic.h:107 include/linux/atomic/atomic-arch-fallback.h:2170 include/linux/atomic/atomic-instrumented.h:1302 include/asm-generic/qspinlock.h:111 include/linux/spinlock.h:187 include/linux/spinlock_api_smp.h:111 kernel/locking/spinlock.c:162)
[ 125.473909][ T1430] ? __pfx__raw_spin_lock_irqsave (kernel/locking/spinlock.c:161)
[ 125.482537][ T1430] _destroy_id (drivers/infiniband/core/cma.c:2044) rdma_cm
[ 125.495072][ T1430] nvme_rdma_free_queue (drivers/nvme/host/rdma.c:656 drivers/nvme/host/rdma.c:650) nvme_rdma
[ 125.505827][ T1430] nvme_rdma_reset_ctrl_work (drivers/nvme/host/rdma.c:2180) nvme_rdma
[ 125.505831][ T1430] process_one_work (kernel/workqueue.c:3231)
[ 125.515122][ T1430] worker_thread (kernel/workqueue.c:3306 kernel/workqueue.c:3393)
[ 125.515127][ T1430] ? __pfx_worker_thread (kernel/workqueue.c:3339)
[ 125.531837][ T1430] kthread (kernel/kthread.c:389)
[ 125.539864][ T1430] ? __pfx_kthread (kernel/kthread.c:342)
[ 125.550628][ T1430] ret_from_fork (arch/x86/kernel/process.c:147)
[ 125.558840][ T1430] ? __pfx_kthread (kernel/kthread.c:342)
[ 125.558844][ T1430] ret_from_fork_asm (arch/x86/entry/entry_64.S:257)
[ 125.566487][ T1430] </TASK>
[ 125.566488][ T1430] ---[ end trace 0000000000000000 ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
fou: fix initialization of grc
The grc must be initialize first. There can be a condition where if
fou is NULL, goto out will be executed and grc would be used
uninitialized. |
| In the Linux kernel, the following vulnerability has been resolved:
net: dpaa: Pad packets to ETH_ZLEN
When sending packets under 60 bytes, up to three bytes of the buffer
following the data may be leaked. Avoid this by extending all packets to
ETH_ZLEN, ensuring nothing is leaked in the padding. This bug can be
reproduced by running
$ ping -s 11 destination |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (adc128d818) Fix underflows seen when writing limit attributes
DIV_ROUND_CLOSEST() after kstrtol() results in an underflow if a large
negative number such as -9223372036854775808 is provided by the user.
Fix it by reordering clamp_val() and DIV_ROUND_CLOSEST() operations. |
| In the Linux kernel, the following vulnerability has been resolved:
Squashfs: sanity check symbolic link size
Syzkiller reports a "KMSAN: uninit-value in pick_link" bug.
This is caused by an uninitialised page, which is ultimately caused
by a corrupted symbolic link size read from disk.
The reason why the corrupted symlink size causes an uninitialised
page is due to the following sequence of events:
1. squashfs_read_inode() is called to read the symbolic
link from disk. This assigns the corrupted value
3875536935 to inode->i_size.
2. Later squashfs_symlink_read_folio() is called, which assigns
this corrupted value to the length variable, which being a
signed int, overflows producing a negative number.
3. The following loop that fills in the page contents checks that
the copied bytes is less than length, which being negative means
the loop is skipped, producing an uninitialised page.
This patch adds a sanity check which checks that the symbolic
link size is not larger than expected.
--
V2: fix spelling mistake. |
| In the Linux kernel, the following vulnerability has been resolved:
of/irq: Prevent device address out-of-bounds read in interrupt map walk
When of_irq_parse_raw() is invoked with a device address smaller than
the interrupt parent node (from #address-cells property), KASAN detects
the following out-of-bounds read when populating the initial match table
(dyndbg="func of_irq_parse_* +p"):
OF: of_irq_parse_one: dev=/soc@0/picasso/watchdog, index=0
OF: parent=/soc@0/pci@878000000000/gpio0@17,0, intsize=2
OF: intspec=4
OF: of_irq_parse_raw: ipar=/soc@0/pci@878000000000/gpio0@17,0, size=2
OF: -> addrsize=3
==================================================================
BUG: KASAN: slab-out-of-bounds in of_irq_parse_raw+0x2b8/0x8d0
Read of size 4 at addr ffffff81beca5608 by task bash/764
CPU: 1 PID: 764 Comm: bash Tainted: G O 6.1.67-484c613561-nokia_sm_arm64 #1
Hardware name: Unknown Unknown Product/Unknown Product, BIOS 2023.01-12.24.03-dirty 01/01/2023
Call trace:
dump_backtrace+0xdc/0x130
show_stack+0x1c/0x30
dump_stack_lvl+0x6c/0x84
print_report+0x150/0x448
kasan_report+0x98/0x140
__asan_load4+0x78/0xa0
of_irq_parse_raw+0x2b8/0x8d0
of_irq_parse_one+0x24c/0x270
parse_interrupts+0xc0/0x120
of_fwnode_add_links+0x100/0x2d0
fw_devlink_parse_fwtree+0x64/0xc0
device_add+0xb38/0xc30
of_device_add+0x64/0x90
of_platform_device_create_pdata+0xd0/0x170
of_platform_bus_create+0x244/0x600
of_platform_notify+0x1b0/0x254
blocking_notifier_call_chain+0x9c/0xd0
__of_changeset_entry_notify+0x1b8/0x230
__of_changeset_apply_notify+0x54/0xe4
of_overlay_fdt_apply+0xc04/0xd94
...
The buggy address belongs to the object at ffffff81beca5600
which belongs to the cache kmalloc-128 of size 128
The buggy address is located 8 bytes inside of
128-byte region [ffffff81beca5600, ffffff81beca5680)
The buggy address belongs to the physical page:
page:00000000230d3d03 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1beca4
head:00000000230d3d03 order:1 compound_mapcount:0 compound_pincount:0
flags: 0x8000000000010200(slab|head|zone=2)
raw: 8000000000010200 0000000000000000 dead000000000122 ffffff810000c300
raw: 0000000000000000 0000000000200020 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffffff81beca5500: 04 fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffffff81beca5580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffffff81beca5600: 00 fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffffff81beca5680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffffff81beca5700: 00 00 00 00 00 00 fc fc fc fc fc fc fc fc fc fc
==================================================================
OF: -> got it !
Prevent the out-of-bounds read by copying the device address into a
buffer of sufficient size. |
| An issue was discovered in libexpat before 2.6.3. nextScaffoldPart in xmlparse.c can have an integer overflow for m_groupSize on 32-bit platforms (where UINT_MAX equals SIZE_MAX). |
| An issue was discovered in libexpat before 2.6.3. dtdCopy in xmlparse.c can have an integer overflow for nDefaultAtts on 32-bit platforms (where UINT_MAX equals SIZE_MAX). |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: prevent UAF in ip6_send_skb()
syzbot reported an UAF in ip6_send_skb() [1]
After ip6_local_out() has returned, we no longer can safely
dereference rt, unless we hold rcu_read_lock().
A similar issue has been fixed in commit
a688caa34beb ("ipv6: take rcu lock in rawv6_send_hdrinc()")
Another potential issue in ip6_finish_output2() is handled in a
separate patch.
[1]
BUG: KASAN: slab-use-after-free in ip6_send_skb+0x18d/0x230 net/ipv6/ip6_output.c:1964
Read of size 8 at addr ffff88806dde4858 by task syz.1.380/6530
CPU: 1 UID: 0 PID: 6530 Comm: syz.1.380 Not tainted 6.11.0-rc3-syzkaller-00306-gdf6cbc62cc9b #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 08/06/2024
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:93 [inline]
dump_stack_lvl+0x241/0x360 lib/dump_stack.c:119
print_address_description mm/kasan/report.c:377 [inline]
print_report+0x169/0x550 mm/kasan/report.c:488
kasan_report+0x143/0x180 mm/kasan/report.c:601
ip6_send_skb+0x18d/0x230 net/ipv6/ip6_output.c:1964
rawv6_push_pending_frames+0x75c/0x9e0 net/ipv6/raw.c:588
rawv6_sendmsg+0x19c7/0x23c0 net/ipv6/raw.c:926
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0x1a6/0x270 net/socket.c:745
sock_write_iter+0x2dd/0x400 net/socket.c:1160
do_iter_readv_writev+0x60a/0x890
vfs_writev+0x37c/0xbb0 fs/read_write.c:971
do_writev+0x1b1/0x350 fs/read_write.c:1018
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f936bf79e79
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 a8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f936cd7f038 EFLAGS: 00000246 ORIG_RAX: 0000000000000014
RAX: ffffffffffffffda RBX: 00007f936c115f80 RCX: 00007f936bf79e79
RDX: 0000000000000001 RSI: 0000000020000040 RDI: 0000000000000004
RBP: 00007f936bfe7916 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 0000000000000000 R14: 00007f936c115f80 R15: 00007fff2860a7a8
</TASK>
Allocated by task 6530:
kasan_save_stack mm/kasan/common.c:47 [inline]
kasan_save_track+0x3f/0x80 mm/kasan/common.c:68
unpoison_slab_object mm/kasan/common.c:312 [inline]
__kasan_slab_alloc+0x66/0x80 mm/kasan/common.c:338
kasan_slab_alloc include/linux/kasan.h:201 [inline]
slab_post_alloc_hook mm/slub.c:3988 [inline]
slab_alloc_node mm/slub.c:4037 [inline]
kmem_cache_alloc_noprof+0x135/0x2a0 mm/slub.c:4044
dst_alloc+0x12b/0x190 net/core/dst.c:89
ip6_blackhole_route+0x59/0x340 net/ipv6/route.c:2670
make_blackhole net/xfrm/xfrm_policy.c:3120 [inline]
xfrm_lookup_route+0xd1/0x1c0 net/xfrm/xfrm_policy.c:3313
ip6_dst_lookup_flow+0x13e/0x180 net/ipv6/ip6_output.c:1257
rawv6_sendmsg+0x1283/0x23c0 net/ipv6/raw.c:898
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0x1a6/0x270 net/socket.c:745
____sys_sendmsg+0x525/0x7d0 net/socket.c:2597
___sys_sendmsg net/socket.c:2651 [inline]
__sys_sendmsg+0x2b0/0x3a0 net/socket.c:2680
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Freed by task 45:
kasan_save_stack mm/kasan/common.c:47 [inline]
kasan_save_track+0x3f/0x80 mm/kasan/common.c:68
kasan_save_free_info+0x40/0x50 mm/kasan/generic.c:579
poison_slab_object+0xe0/0x150 mm/kasan/common.c:240
__kasan_slab_free+0x37/0x60 mm/kasan/common.c:256
kasan_slab_free include/linux/kasan.h:184 [inline]
slab_free_hook mm/slub.c:2252 [inline]
slab_free mm/slub.c:4473 [inline]
kmem_cache_free+0x145/0x350 mm/slub.c:4548
dst_destroy+0x2ac/0x460 net/core/dst.c:124
rcu_do_batch kernel/rcu/tree.c:2569 [inline]
rcu_core+0xafd/0x1830 kernel/rcu/tree.
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
exec: Fix ToCToU between perm check and set-uid/gid usage
When opening a file for exec via do_filp_open(), permission checking is
done against the file's metadata at that moment, and on success, a file
pointer is passed back. Much later in the execve() code path, the file
metadata (specifically mode, uid, and gid) is used to determine if/how
to set the uid and gid. However, those values may have changed since the
permissions check, meaning the execution may gain unintended privileges.
For example, if a file could change permissions from executable and not
set-id:
---------x 1 root root 16048 Aug 7 13:16 target
to set-id and non-executable:
---S------ 1 root root 16048 Aug 7 13:16 target
it is possible to gain root privileges when execution should have been
disallowed.
While this race condition is rare in real-world scenarios, it has been
observed (and proven exploitable) when package managers are updating
the setuid bits of installed programs. Such files start with being
world-executable but then are adjusted to be group-exec with a set-uid
bit. For example, "chmod o-x,u+s target" makes "target" executable only
by uid "root" and gid "cdrom", while also becoming setuid-root:
-rwxr-xr-x 1 root cdrom 16048 Aug 7 13:16 target
becomes:
-rwsr-xr-- 1 root cdrom 16048 Aug 7 13:16 target
But racing the chmod means users without group "cdrom" membership can
get the permission to execute "target" just before the chmod, and when
the chmod finishes, the exec reaches brpm_fill_uid(), and performs the
setuid to root, violating the expressed authorization of "only cdrom
group members can setuid to root".
Re-check that we still have execute permissions in case the metadata
has changed. It would be better to keep a copy from the perm-check time,
but until we can do that refactoring, the least-bad option is to do a
full inode_permission() call (under inode lock). It is understood that
this is safe against dead-locks, but hardly optimal. |
| In the Linux kernel, the following vulnerability has been resolved:
jfs: Fix array-index-out-of-bounds in diFree |
| In the Linux kernel, the following vulnerability has been resolved:
leds: trigger: Unregister sysfs attributes before calling deactivate()
Triggers which have trigger specific sysfs attributes typically store
related data in trigger-data allocated by the activate() callback and
freed by the deactivate() callback.
Calling device_remove_groups() after calling deactivate() leaves a window
where the sysfs attributes show/store functions could be called after
deactivation and then operate on the just freed trigger-data.
Move the device_remove_groups() call to before deactivate() to close
this race window.
This also makes the deactivation path properly do things in reverse order
of the activation path which calls the activate() callback before calling
device_add_groups(). |
| In the Linux kernel, the following vulnerability has been resolved:
PCI/DPC: Fix use-after-free on concurrent DPC and hot-removal
Keith reports a use-after-free when a DPC event occurs concurrently to
hot-removal of the same portion of the hierarchy:
The dpc_handler() awaits readiness of the secondary bus below the
Downstream Port where the DPC event occurred. To do so, it polls the
config space of the first child device on the secondary bus. If that
child device is concurrently removed, accesses to its struct pci_dev
cause the kernel to oops.
That's because pci_bridge_wait_for_secondary_bus() neglects to hold a
reference on the child device. Before v6.3, the function was only
called on resume from system sleep or on runtime resume. Holding a
reference wasn't necessary back then because the pciehp IRQ thread
could never run concurrently. (On resume from system sleep, IRQs are
not enabled until after the resume_noirq phase. And runtime resume is
always awaited before a PCI device is removed.)
However starting with v6.3, pci_bridge_wait_for_secondary_bus() is also
called on a DPC event. Commit 53b54ad074de ("PCI/DPC: Await readiness
of secondary bus after reset"), which introduced that, failed to
appreciate that pci_bridge_wait_for_secondary_bus() now needs to hold a
reference on the child device because dpc_handler() and pciehp may
indeed run concurrently. The commit was backported to v5.10+ stable
kernels, so that's the oldest one affected.
Add the missing reference acquisition.
Abridged stack trace:
BUG: unable to handle page fault for address: 00000000091400c0
CPU: 15 PID: 2464 Comm: irq/53-pcie-dpc 6.9.0
RIP: pci_bus_read_config_dword+0x17/0x50
pci_dev_wait()
pci_bridge_wait_for_secondary_bus()
dpc_reset_link()
pcie_do_recovery()
dpc_handler() |
| In the Linux kernel, the following vulnerability has been resolved:
kobject_uevent: Fix OOB access within zap_modalias_env()
zap_modalias_env() wrongly calculates size of memory block to move, so
will cause OOB memory access issue if variable MODALIAS is not the last
one within its @env parameter, fixed by correcting size to memmove. |
| In the Linux kernel, the following vulnerability has been resolved:
net/iucv: Avoid explicit cpumask var allocation on stack
For CONFIG_CPUMASK_OFFSTACK=y kernel, explicit allocation of cpumask
variable on stack is not recommended since it can cause potential stack
overflow.
Instead, kernel code should always use *cpumask_var API(s) to allocate
cpumask var in config-neutral way, leaving allocation strategy to
CONFIG_CPUMASK_OFFSTACK.
Use *cpumask_var API(s) to address it. |
