| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: ctnetlink: use netlink policy range checks
Replace manual range and mask validations with netlink policy
annotations in ctnetlink code paths, so that the netlink core rejects
invalid values early and can generate extack errors.
- CTA_PROTOINFO_TCP_STATE: reject values > TCP_CONNTRACK_SYN_SENT2 at
policy level, removing the manual >= TCP_CONNTRACK_MAX check.
- CTA_PROTOINFO_TCP_WSCALE_ORIGINAL/REPLY: reject values > TCP_MAX_WSCALE
(14). The normal TCP option parsing path already clamps to this value,
but the ctnetlink path accepted 0-255, causing undefined behavior when
used as a u32 shift count.
- CTA_FILTER_ORIG_FLAGS/REPLY_FLAGS: use NLA_POLICY_MASK with
CTA_FILTER_F_ALL, removing the manual mask checks.
- CTA_EXPECT_FLAGS: use NLA_POLICY_MASK with NF_CT_EXPECT_MASK, adding
a new mask define grouping all valid expect flags.
Extracted from a broader nf-next patch by Florian Westphal, scoped to
ctnetlink for the fixes tree. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: Fix ERTM re-init and zero pdu_len infinite loop
l2cap_config_req() processes CONFIG_REQ for channels in BT_CONNECTED
state to support L2CAP reconfiguration (e.g. MTU changes). However,
since both CONF_INPUT_DONE and CONF_OUTPUT_DONE are already set from
the initial configuration, the reconfiguration path falls through to
l2cap_ertm_init(), which re-initializes tx_q, srej_q, srej_list, and
retrans_list without freeing the previous allocations and sets
chan->sdu to NULL without freeing the existing skb. This leaks all
previously allocated ERTM resources.
Additionally, l2cap_parse_conf_req() does not validate the minimum
value of remote_mps derived from the RFC max_pdu_size option. A zero
value propagates to l2cap_segment_sdu() where pdu_len becomes zero,
causing the while loop to never terminate since len is never
decremented, exhausting all available memory.
Fix the double-init by skipping l2cap_ertm_init() and
l2cap_chan_ready() when the channel is already in BT_CONNECTED state,
while still allowing the reconfiguration parameters to be updated
through l2cap_parse_conf_req(). Also add a pdu_len zero check in
l2cap_segment_sdu() as a safeguard. |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: cdc-phonet: fix skb frags[] overflow in rx_complete()
A malicious USB device claiming to be a CDC Phonet modem can overflow
the skb_shared_info->frags[] array by sending an unbounded sequence of
full-page bulk transfers.
Drop the skb and increment the length error when the frag limit is
reached. This matches the same fix that commit f0813bcd2d9d ("net:
wwan: t7xx: fix potential skb->frags overflow in RX path") did for the
t7xx driver. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usx2y: us144mkii: fix NULL deref on missing interface 0
A malicious USB device with the TASCAM US-144MKII device id can have a
configuration containing bInterfaceNumber=1 but no interface 0. USB
configuration descriptors are not required to assign interface numbers
sequentially, so usb_ifnum_to_if(dev, 0) returns will NULL, which will
then be dereferenced directly.
Fix this up by checking the return value properly. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: fireworks: bound device-supplied status before string array lookup
The status field in an EFW response is a 32-bit value supplied by the
firewire device. efr_status_names[] has 17 entries so a status value
outside that range goes off into the weeds when looking at the %s value.
Even worse, the status could return EFR_STATUS_INCOMPLETE which is
0x80000000, and is obviously not in that array of potential strings.
Fix this up by properly bounding the index against the array size and
printing "unknown" if it's not recognized. |
| In the Linux kernel, the following vulnerability has been resolved:
fbdev: tdfxfb: avoid divide-by-zero on FBIOPUT_VSCREENINFO
Much like commit 19f953e74356 ("fbdev: fb_pm2fb: Avoid potential divide
by zero error"), we also need to prevent that same crash from happening
in the udlfb driver as it uses pixclock directly when dividing, which
will crash. |
| In the Linux kernel, the following vulnerability has been resolved:
bnge: return after auxiliary_device_uninit() in error path
When auxiliary_device_add() fails, the error block calls
auxiliary_device_uninit() but does not return. The uninit drops the
last reference and synchronously runs bnge_aux_dev_release(), which sets
bd->auxr_dev = NULL and frees the underlying object. The subsequent
bd->auxr_dev->net = bd->netdev then dereferences NULL, which is not a
good thing to have happen when trying to clean up from an error.
Add the missing return, as the auxiliary bus documentation states is a
requirement (seems that LLM tools read documentation better than humans
do...) |
| In the Linux kernel, the following vulnerability has been resolved:
HID: core: clamp report_size in s32ton() to avoid undefined shift
s32ton() shifts by n-1 where n is the field's report_size, a value that
comes directly from a HID device. The HID parser bounds report_size
only to <= 256, so a broken HID device can supply a report descriptor
with a wide field that triggers shift exponents up to 256 on a 32-bit
type when an output report is built via hid_output_field() or
hid_set_field().
Commit ec61b41918587 ("HID: core: fix shift-out-of-bounds in
hid_report_raw_event") added the same n > 32 clamp to the function
snto32(), but s32ton() was never given the same fix as I guess syzbot
hadn't figured out how to fuzz a device the same way.
Fix this up by just clamping the max value of n, just like snto32()
does. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ti: icssg-prueth: fix use-after-free of CPPI descriptor in RX path
cppi5_hdesc_get_psdata() returns a pointer into the CPPI descriptor.
In both emac_rx_packet() and emac_rx_packet_zc(), the descriptor is
freed via k3_cppi_desc_pool_free() before the psdata pointer is used
by emac_rx_timestamp(), which dereferences psdata[0] and psdata[1].
This constitutes a use-after-free on every received packet that goes
through the timestamp path.
Defer the descriptor free until after all accesses through the psdata
pointer are complete. For emac_rx_packet(), move the free into the
requeue label so both early-exit and success paths free the descriptor
after all accesses are done. For emac_rx_packet_zc(), move the free to
the end of the loop body after emac_dispatch_skb_zc() (which calls
emac_rx_timestamp()) has returned. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/entry: Scrub r12 register on kernel entry
Before commit f33f2d4c7c80 ("s390/bp: remove TIF_ISOLATE_BP"),
all entry handlers loaded r12 with the current task pointer
(lg %r12,__LC_CURRENT) for use by the BPENTER/BPEXIT macros. That
commit removed TIF_ISOLATE_BP, dropping both the branch prediction
macros and the r12 load, but did not add r12 to the register clearing
sequence.
Add the missing xgr %r12,%r12 to make the register scrub consistent
across all entry points. |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring/fdinfo: fix OOB read in SQE_MIXED wrap check
__io_uring_show_fdinfo() iterates over pending SQEs and, for 128-byte
SQEs on an IORING_SETUP_SQE_MIXED ring, needs to detect when the second
half of the SQE would be past the end of the sq_sqes array. The current
check tests (++sq_head & sq_mask) == 0, but sq_head is only incremented
when a 128-byte SQE is encountered, not on every iteration. The actual
array index is sq_idx = (i + sq_head) & sq_mask, which can be sq_mask
(the last slot) while the wrap check passes.
Fix by checking sq_idx directly. Keep the sq_head increment so the loop
still skips the second half of the 128-byte SQE on the next iteration. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: spi-fsl-lpspi: fix teardown order issue (UAF)
There is a teardown order issue in the driver. The SPI controller is
registered using devm_spi_register_controller(), which delays
unregistration of the SPI controller until after the fsl_lpspi_remove()
function returns.
As the fsl_lpspi_remove() function synchronously tears down the DMA
channels, a running SPI transfer triggers the following NULL pointer
dereference due to use after free:
| fsl_lpspi 42550000.spi: I/O Error in DMA RX
| Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
[...]
| Call trace:
| fsl_lpspi_dma_transfer+0x260/0x340 [spi_fsl_lpspi]
| fsl_lpspi_transfer_one+0x198/0x448 [spi_fsl_lpspi]
| spi_transfer_one_message+0x49c/0x7c8
| __spi_pump_transfer_message+0x120/0x420
| __spi_sync+0x2c4/0x520
| spi_sync+0x34/0x60
| spidev_message+0x20c/0x378 [spidev]
| spidev_ioctl+0x398/0x750 [spidev]
[...]
Switch from devm_spi_register_controller() to spi_register_controller() in
fsl_lpspi_probe() and add the corresponding spi_unregister_controller() in
fsl_lpspi_remove(). |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Do not skip unrelated mode changes in DSC validation
Starting with commit 17ce8a6907f7 ("drm/amd/display: Add dsc pre-validation in
atomic check"), amdgpu resets the CRTC state mode_changed flag to false when
recomputing the DSC configuration results in no timing change for a particular
stream.
However, this is incorrect in scenarios where a change in MST/DSC configuration
happens in the same KMS commit as another (unrelated) mode change. For example,
the integrated panel of a laptop may be configured differently (e.g., HDR
enabled/disabled) depending on whether external screens are attached. In this
case, plugging in external DP-MST screens may result in the mode_changed flag
being dropped incorrectly for the integrated panel if its DSC configuration
did not change during precomputation in pre_validate_dsc().
At this point, however, dm_update_crtc_state() has already created new streams
for CRTCs with DSC-independent mode changes. In turn,
amdgpu_dm_commit_streams() will never release the old stream, resulting in a
memory leak. amdgpu_dm_atomic_commit_tail() will never acquire a reference to
the new stream either, which manifests as a use-after-free when the stream gets
disabled later on:
BUG: KASAN: use-after-free in dc_stream_release+0x25/0x90 [amdgpu]
Write of size 4 at addr ffff88813d836524 by task kworker/9:9/29977
Workqueue: events drm_mode_rmfb_work_fn
Call Trace:
<TASK>
dump_stack_lvl+0x6e/0xa0
print_address_description.constprop.0+0x88/0x320
? dc_stream_release+0x25/0x90 [amdgpu]
print_report+0xfc/0x1ff
? srso_alias_return_thunk+0x5/0xfbef5
? __virt_addr_valid+0x225/0x4e0
? dc_stream_release+0x25/0x90 [amdgpu]
kasan_report+0xe1/0x180
? dc_stream_release+0x25/0x90 [amdgpu]
kasan_check_range+0x125/0x200
dc_stream_release+0x25/0x90 [amdgpu]
dc_state_destruct+0x14d/0x5c0 [amdgpu]
dc_state_release.part.0+0x4e/0x130 [amdgpu]
dm_atomic_destroy_state+0x3f/0x70 [amdgpu]
drm_atomic_state_default_clear+0x8ee/0xf30
? drm_mode_object_put.part.0+0xb1/0x130
__drm_atomic_state_free+0x15c/0x2d0
atomic_remove_fb+0x67e/0x980
Since there is no reliable way of figuring out whether a CRTC has unrelated
mode changes pending at the time of DSC validation, remember the value of the
mode_changed flag from before the point where a CRTC was marked as potentially
affected by a change in DSC configuration. Reset the mode_changed flag to this
earlier value instead in pre_validate_dsc().
(cherry picked from commit cc7c7121ae082b7b82891baa7280f1ff2608f22b) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/pf: Fix use-after-free in migration restore
When an error is returned from xe_sriov_pf_migration_restore_produce(),
the data pointer is not set to NULL, which can trigger use-after-free
in subsequent .write() calls.
Set the pointer to NULL upon error to fix the problem.
(cherry picked from commit 4f53d8c6d23527d734fe3531d08e15cb170a0819) |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/irdma: Harden depth calculation functions
An issue was exposed where OS can pass in U32_MAX for SQ/RQ/SRQ size.
This can cause integer overflow and truncation of SQ/RQ/SRQ depth
returning a success when it should have failed.
Harden the functions to do all depth calculations and boundary
checking in u64 sizes. |
| In the Linux kernel, the following vulnerability has been resolved:
idpf: check error for register_netdev() on init
Current init logic ignores the error code from register_netdev(),
which will cause WARN_ON() on attempt to unregister it, if there was one,
and there is no info for the user that the creation of the netdev failed.
WARNING: CPU: 89 PID: 6902 at net/core/dev.c:11512 unregister_netdevice_many_notify+0x211/0x1a10
...
[ 3707.563641] unregister_netdev+0x1c/0x30
[ 3707.563656] idpf_vport_dealloc+0x5cf/0xce0 [idpf]
[ 3707.563684] idpf_deinit_task+0xef/0x160 [idpf]
[ 3707.563712] idpf_vc_core_deinit+0x84/0x320 [idpf]
[ 3707.563739] idpf_remove+0xbf/0x780 [idpf]
[ 3707.563769] pci_device_remove+0xab/0x1e0
[ 3707.563786] device_release_driver_internal+0x371/0x530
[ 3707.563803] driver_detach+0xbf/0x180
[ 3707.563816] bus_remove_driver+0x11b/0x2a0
[ 3707.563829] pci_unregister_driver+0x2a/0x250
Introduce an error check and log the vport number and error code.
On removal make sure to check VPORT_REG_NETDEV flag prior to calling
unregister and free on the netdev.
Add local variables for idx, vport_config and netdev for readability. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Drain deferred trigger frees if kthread creation fails
Boot-time trigger registration can fail before the trigger-data cleanup
kthread exists. Deferring those frees until late init is fine, but the
post-boot fallback must still drain the deferred list if kthread
creation never succeeds.
Otherwise, boot-deferred nodes can accumulate on
trigger_data_free_list, later frees fall back to synchronously freeing
only the current object, and the older queued entries are leaked
forever.
To trigger this, add the following to the kernel command line:
trace_event=sched_switch trace_trigger=sched_switch.traceon,sched_switch.traceon
The second traceon trigger will fail and be freed. This triggers a NULL
pointer dereference and crashes the kernel.
Keep the deferred boot-time behavior, but when kthread creation fails,
drain the whole queued list synchronously. Do the same in the late-init
drain path so queued entries are not stranded there either. |
| In the Linux kernel, the following vulnerability has been resolved:
media: nxp: imx8-isi: Fix streaming cleanup on release
The current implementation unconditionally calls
mxc_isi_video_cleanup_streaming() in mxc_isi_video_release(). This can
lead to situations where any release call (like from a simple
"v4l2-ctl -l") may release a currently streaming queue when called on
such a device.
This is reproducible on an i.MX8MP board by streaming from an ISI
capture device using gstreamer:
gst-launch-1.0 -v v4l2src device=/dev/videoX ! \
video/x-raw,format=GRAY8,width=1280,height=800,framerate=1/120 ! \
fakesink
While this stream is running, querying the caps of the same device
provokes the error state:
v4l2-ctl -l -d /dev/videoX
This results in the following trace:
[ 155.452152] ------------[ cut here ]------------
[ 155.452163] WARNING: CPU: 0 PID: 1708 at drivers/media/platform/nxp/imx8-isi/imx8-isi-pipe.c:713 mxc_isi_pipe_irq_handler+0x19c/0x1b0 [imx8_isi]
[ 157.004248] Modules linked in: cfg80211 rpmsg_ctrl rpmsg_char rpmsg_tty virtio_rpmsg_bus rpmsg_ns rpmsg_core rfkill nft_ct nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables mcp251x6
[ 157.053499] CPU: 0 UID: 0 PID: 1708 Comm: python3 Not tainted 6.15.4-00114-g1f61ca5cad76 #1 PREEMPT
[ 157.064369] Hardware name: imx8mp_board_01 (DT)
[ 157.068205] pstate: 400000c5 (nZcv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 157.075169] pc : mxc_isi_pipe_irq_handler+0x19c/0x1b0 [imx8_isi]
[ 157.081195] lr : mxc_isi_pipe_irq_handler+0x38/0x1b0 [imx8_isi]
[ 157.087126] sp : ffff800080003ee0
[ 157.090438] x29: ffff800080003ee0 x28: ffff0000c3688000 x27: 0000000000000000
[ 157.097580] x26: 0000000000000000 x25: ffff0000c1e7ac00 x24: ffff800081b5ad50
[ 157.104723] x23: 00000000000000d1 x22: 0000000000000000 x21: ffff0000c25e4000
[ 157.111866] x20: 0000000060000200 x19: ffff80007a0608d0 x18: 0000000000000000
[ 157.119008] x17: ffff80006a4e3000 x16: ffff800080000000 x15: 0000000000000000
[ 157.126146] x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000
[ 157.133287] x11: 0000000000000040 x10: ffff0000c01445f0 x9 : ffff80007a053a38
[ 157.140425] x8 : ffff0000c04004b8 x7 : 0000000000000000 x6 : 0000000000000000
[ 157.147567] x5 : ffff0000c0400490 x4 : ffff80006a4e3000 x3 : ffff0000c25e4000
[ 157.154706] x2 : 0000000000000000 x1 : ffff8000825c0014 x0 : 0000000060000200
[ 157.161850] Call trace:
[ 157.164296] mxc_isi_pipe_irq_handler+0x19c/0x1b0 [imx8_isi] (P)
[ 157.170319] __handle_irq_event_percpu+0x58/0x218
[ 157.175029] handle_irq_event+0x54/0xb8
[ 157.178867] handle_fasteoi_irq+0xac/0x248
[ 157.182968] handle_irq_desc+0x48/0x68
[ 157.186723] generic_handle_domain_irq+0x24/0x38
[ 157.191346] gic_handle_irq+0x54/0x120
[ 157.195098] call_on_irq_stack+0x24/0x30
[ 157.199027] do_interrupt_handler+0x88/0x98
[ 157.203212] el0_interrupt+0x44/0xc0
[ 157.206792] __el0_irq_handler_common+0x18/0x28
[ 157.211328] el0t_64_irq_handler+0x10/0x20
[ 157.215429] el0t_64_irq+0x198/0x1a0
[ 157.219009] ---[ end trace 0000000000000000 ]---
Address this issue by moving the streaming preparation and cleanup to
the vb2 .prepare_streaming() and .unprepare_streaming() operations. This
also simplifies the driver by allowing direct usage of the
vb2_ioctl_streamon() and vb2_ioctl_streamoff() helpers, and removal of
the manual cleanup from mxc_isi_video_release(). |
| Out of bounds read in GPU in Google Chrome on Android prior to 147.0.7727.117 allowed a remote attacker who had compromised the renderer process to potentially perform a sandbox escape via a crafted HTML page. (Chromium security severity: High) |
| Race in GPU in Google Chrome on Windows prior to 147.0.7727.117 allowed a remote attacker to potentially perform a sandbox escape via a crafted video file. (Chromium security severity: Medium) |
